Multifunction units for 4-pipe systems of GPE N Kc Kr series are suitable for outdoor installation and are particularly indicated to cool pure fluid solutions or containing glycol for industrial applications or in air conditioning systems of the service industry where it is necessary to grant excellent performances and a very low environmental impact.

The units are designed for external installation, in compliance with the European standard EN 378 and relevant updates. Depending on the capacity required the units are available with 1 or 2 independents cooling circuits equipped with 1 or 2 compressors for every circuit (tandem configuration). 

Thanks to the many available options, these chillers are particularly versatile and are easily adaptable to the different types of plants, where production of chilled or heat water is required.

All the units are completely factory assembled, tested and supplied with refrigerant plus non-freezing oil; so, once on installation site, they only need to be positioned and connected to the hydraulic and power supply lines.

Multipurpose units, ideal for all installed applications where simultaneous production of hot and cold water is required, through the use of dedicated, independent circuits in 2- or 4-pipe hydronic systems. 

The polyvalent represents an effective and convenient alternative to traditional solutions (Boiler + Chiller) with a particular energy benefit in the conditions of demand for both fluids, hot and cold, concurrently.

The refrigerant used is Propane, a non-toxic hydrocarbon, even at high concentrations, with almost a null ozone depletion potential, negligible global warming potential and thermodynamic properties which allow to reach high efficiency values. For this reason the units are designed for external installation, in compliance with the European standard EN378 and his updates. 

Thanks to the many available options, these heat pumps are particularly versatile and are easily adaptable to the different types of plant, where production of chilled water is required.

All the units are completely factory assembled, tested and supplied with refrigerant non-freezing oil charge; so, once on installation site, they only need to be positioned and connected to the hydraulic and power supply lines.

WHA heat pumps are particularly suitable for applications that utilise ground source probes.These units have been designed for use with radiant floor heating systems or those applications where it is necessary to have maximum efficiency when heating.

They have been optimized on heating mode and are able to produce water up to 60°C. WHA heat pumps are available in several versions. The most simple is a 2 pipe unit that can provide heating only. By fitting an external 3 port valve the unit can provide either heating or domestic hot water. There is also a 4 pipe unit that produces domestic hot water in a separate hydraulic circuit and can generate this irrespective of whether the unit is in heating or cooling mode.

All the WHA units are also available in Free Cooling (FC) versions which provide low energy cooling by simply using the cool water that is available from either the ground source probes or the well water.

Differing versions and a wide range of accessories, enable the optimal solution to be selected.

WZA heat pumps are particularly suitable for applications that utilise well water or ground source probes. These units have been designed for use with radiant floor heating systems or those applications where it is necessary to have maximum efficiency when heating.

They have been optimized on heating mode and are able to produce water up to 60°C. WZA heat pumps are available in several versions. The most simple is a 2 pipe unit that can provide heating only. By fitting an external 3 port valve the unit can provide either heating or domestic hot water. 

There is also a 4 pipe unit that produces domestic hot water in a separate hydraulic circuit and can generate this irrespective of whether the unit is in heating or cooling mode.

Differing versions and a wide range of accessories, enable the optimal solution to be selected.

The air source high efficiency heat pumps WZT series, in the NN configuration, are particularly suitable for those applications where it is necessary to have maximum efficiency in heating mode and a noise level extremely low and, for this purpose, are provided in two sections, linked together by refrigerant lines, installing the compressor in the internal section.

The units have been designed specifically to have the best possible efficiency, they may operate down to ambient temperatures of -20°C and produce hot water up to 65°C. The units are available in 2-pipe (P2S, P2U), version 2 + 2 pipe (P4S), and in version 4 pipe (P4U). 

The units P2U are not able to produce sanitary hot water, the P2S versions are able to produce domestic hot water through the activation of an external 3-way valve (not supplied), while P4S versions and P4U too are able to produce hot water regardless of the mode unit is operating, through the activation of a specific refrigerating circuit.

All models are equipped with reverse cycle valve for winter defrost mode, RV versions are also able to produce cold water in summer (not available for HH version). The noise level is extremely contained thanks to the use of a special floating system vibration damping that enables a reduction in terms of noise about 6-8 db (A) of compressors side and the fans in the combination with the specific number of turns extremely low (about 450 rpm).

The high efficiency air / water heat pumps of the LZT/P4 series are units designed for 4-pipe air conditioning and heating systems, which allow the production of cold water for cooling and hot water for heating at the same time or separately.

The units are supplied with an additional exchanger, used as a condenser for hot water, the production of which is independent of the operation mode of the unit. Activation of the exchanger takes place automatically via the microprocessor control when the hot water temperature on the return is lower than the set point. These units are able to produce hot water and cold water simultaneously and / or separately with very high energy efficiencies.

They are all supplied complete with a specific advanced microprocessor control provided with software for managing the various priorities.

The XL versions also have an extremely low noise level thanks to the use of a special floating vibration damping system that allows a noise reduction of about 6-8 dB (A) (optional)

The LZT series of high efficiency heat pumps has been specifically designed for use with radiant floor heating systems or those applications where it is necessary to have maximum efficiency when heating.

They have been optimized on heating mode, are able to produce water up to 65°C and can operate down to -20°C ambient temperature.

All versions are supplied with reverse cycle valve used for winter defrost; the HH version is suitable for use in those countries that have support schemes for use of heat pump technology for heating. 

The RV versions are also able to produce cold water. The HH heating only versions is factory set and locked to operate only in heating mode whilst.

The noise in XL and NN versions is extremely low thanks to the use of a special floating vibration damping system which allows a noise reduction of about 6-8 dB(A).

Multipurpose units, ideal for all installed applications where simultaneous production of hot and cold water is required, through the use of dedicated, independent circuits in 2- or 4-pipe hydronic systems.

The polyvalent represents an effective and convenient alternative to traditional solutions (Boiler + Chiller) with a particular energy benefit in the conditions of demand for both fluids, hot and cold, concurrently.
The refrigerant used is Propane, a non-toxic hydrocarbon, even at high concentrations, with almost a null ozone depletion potential, negligible global warming potential and thermodynamic properties which allow
to reach high efficiency values. For this reason the units are designed for external installation, in compliance with the European standard EN378 and his updates. 

Depending on the required heating
capacity, the units are available in mono or multi compressor with 1 or 2 independent cooling circuits.

Thanks to the many available options, these heat pumps are particularly versatile and are easily adaptable to the different types of plant, where production of chilled water is required.

All the units are completely factory assembled, tested and supplied with refrigerant non-freezing oil charge; so, once on installation site, they only need to be positioned and connected to the hydraulic and
power supply lines.

The LHi P4U/P4S series high-efficiency air-to-water heat pumps are units designed for four-pipe air conditioning and heating systems, which allow the simultaneous or separate production of cold water for cooling and hot water for heating.

The units are supplied with an additional exchanger, used as a condenser for hot water, whose production is independent of the unit’s operating mode. The exchanger is automatically activated by microprocessor control when the hot water temperature on the return flow is lower than the set applied.

These units are able to produce hot water and cold water simultaneously and/or separately with very high energy efficiency.

They are all supplied complete with a specific advanced microprocessor control equipped with software for the management of the various priorities.

The XL versions also have an extremely low noise level thanks to the use of a special floating vibration dampening system that allows a noise reduction of about 6-8 dB(A) (optional).

LHE high-efficiency air/water heat pumps are particularly suitable for applications where maximum efficiency in heating mode and a low noise level are required.

The units are specifically designed to provide the best efficiency in heating mode; they can operate at outside temperatures down to -20°C and produce water up to a temperature of 60°C.
All sizez are supplied with reverse cycle valve used for winter defrost; the RV versions are also able to produce cold water in summer period.

EVEREST 290 – GPE Kp series air/water polyvalent unit for modular installation. It is particularly suitable for residential, commercial, and industrial applications that require the simultaneous production of hot water at high temperatures and chilled water, at the highest efficiency levels possible. This unit is specifically designed to reach optimal efficiency levels in heating mode, being able to operate down to outdoor air temperatures of -20°C and ensuring hot water production up to 65°C. The unit design minimizes overall dimensions while ensuring high cooling performance. This is achieved through the use of innovative and high-quality components. Scroll compressors are optimized for high compression ratios. They are used in tandem configuration in conjunction with electronic control of the airflow rate on the source side. This enables the achievement of high seasonal efficiency ratings.

The refrigerant used is Propane, a non-toxic hydrocarbon, even at high concentrations, with almost a null ozone depletion potential, negligible global warming potential and thermodynamic properties which allow to reach high efficiency values. All the units are completely factory assembled, tested and supplied with refrigerant non-freezing oil charge; so, once on installation site, they only need to be positioned and connected to the hydraulic and power supply lines.